![honda hds windows 10 honda hds windows 10](https://australianever692.weebly.com/uploads/1/2/6/1/126127363/258644229.jpg)
- #Honda hds windows 10 how to#
- #Honda hds windows 10 install#
- #Honda hds windows 10 serial#
- #Honda hds windows 10 drivers#
- #Honda hds windows 10 Patch#
As known, HDS is designed for professionals, it covers all honda models, can access all electronic control systems, can perform diagnostics, IMMO programming and ECU programming. THINKCAR Thinkdiag for Honda full system diagnostic scanner is very similar with Honda HIM HDS. This should be done after a wheel alignment, clock spring replace or abs module replace.
#Honda hds windows 10 how to#
How to reset the steering angle sensor to its zero point neutral point on a 2017 Honda Accord using an autel scanner. The program pleased me with its capabilities, it works slowly, of course, but this is not a big problem, it works.Ĭheck Launch X-431 Honda steering angle sensor reset car list below:Īpplied to Autel Maxisys, MaxiCOM, MaxiDAS, MaxiIM IM608 etc series scanners. Launch HDS and select XHorse – MVCI in the communication interface
#Honda hds windows 10 drivers#
Through the Add-Remove Programs we demolish the drivers of dealer scanners SPX MVCI 3.01.37.
#Honda hds windows 10 serial#
Do the same with USB Serial converter and USB Serial Port.Ĩ.Next, go back to “Honda HDS 3.101.019 ” and run the registry file “Xhorse64.reg”.ĩ.
#Honda hds windows 10 install#
Important! Disconnect the Internet because Win10 will automatically find and install the drivers. They won’t work! If Win10 automatically installed drivers from the network, then remove the installed devices (USB Serial converter and USB Serial Port) and remove their drivers. Then connect the cable, it will appear in M-VCI with a yellow question mark, on which we manually install the driver from the C: / XHorse location. Install the drivers manually from the XHorse folder. In the folder “Honda HDS 3.101.019 “, extract the contents of XHorse.zip Extract to the root of the C drive! Add Anti-virusħ.
#Honda hds windows 10 Patch#
Next, look in the extracted folder “Honda HDS 3.101.019 “, run the patch “HIMGNA.exe”Ħ. We are waiting for the end of the installation. Do not start HDS afterwards.ĥ. Select the Europe region. The dealer code is 208342, in my opinion you can do anything.Ĥ. Important! Disable Anti-Virus before installation or add it to the exclusions. Go to the extracted folder “Honda HDS 3.101.019 \ HDS PC”, run “Setup.exe” You are at your risk.ģ.101.019 can be downloaded here for free.Ģ. The procedure here is for version 3.101.019. It’s simple, if you have an earlier version of Windows, you will have to tinker a little for Win10. Now to fight some eBay dude for my money back.Īt least I paid via PayPal should he try to make it difficult.To connect and work, you need to install the Honda HDS program. Ultimately it's swallowed up about 15 hours of my life this week, and guess what the problem is with my guaranteed to work, but used VSA unit? Once I'd done this, setting the USB to COM1 was easy, but finding an appropriate driver for the conversion cable became a 'mare. My fresh XP install wouldn't show COM PORTS under device manager, even though they were on in BIOS.Įventually I managed to get it to display via the add hardware function, but that was through trial and error, as everything on the Internet told me to configure the connection under COM PORTS in device manager, which was my problem anyway. The second nightmare came with configuring the COM1 port for the usb/serial connection. I ended up downloading the software from them direct, which installed as it should've, implying that there was a problem with the disc I was sent. You should then find the cable listed under Ports, and in the Properties for the cable, go to Port Settings, Advanced, where you should have the ability to select COM 1 for the cable.Ĭheers for pointing me in the right direction Freddofrog. When the drivers are installed and the adapter cable is plugged in, on XP you will now find Ports listed in Device Manager. The HDS expects the RS232 on COM PORT 1, but if you are using a USB-to-RS232 adapter-cable, the drivers for it must let you change the COM PORT settings. That PC has full control of the RS232 port-settings in BIOS.
![honda hds windows 10 honda hds windows 10](http://blog.chinacardiags.com/wp-content/uploads/2017/06/honda-hds-3-102-004-diagnostic-software-honda-hds-him-2.jpg)
Fortunately for me, I still have an ancient desktop-PC with built-in RS232, and the first time I used the HDS, I installed and ran it on that PC. If you don't have a built-in RS232 on your platform, you need a USB-to-RS232 adapter-cable and good drivers for it. Thirdly, when you have installed the software, the nightmare is not over. I think the reason that it will copy from CD rather than install from CD, is that there are differences in the way the two processes run. but, the EXE will COPY to desktop (or anywhere you want). The EXE would not install from the mini-CD that came with my HDS clone. Secondly, if it's a clone, yeah the poxy mini-CD that comes with it is low quality. Firstly, it will only install on Windows XP